- LG WASHING MACHINE REPAIR HOW TO
- LG WASHING MACHINE REPAIR GENERATOR
- LG WASHING MACHINE REPAIR MANUAL
- LG WASHING MACHINE REPAIR PATCH
- LG WASHING MACHINE REPAIR CODE
LG WASHING MACHINE REPAIR GENERATOR
Can a Generator Run a Portable Air Conditioner?.How To Fix A TV That Has A Dark Screen – Cannot See Television Picture.Water Heater Troubleshooting Tips – 5 Common Issues.
LG WASHING MACHINE REPAIR PATCH
2 Easy Ways To Patch a Hole In Your Air Mattress.GE Dishwasher Not Starting – 4 Things To Check.100 Cozy Backyard Ideas For All Budgets.Easy Way To Use A Trickle Charger On Your Cars Battery.How To Fix A Garage Door That Is Squeaking?.
LG WASHING MACHINE REPAIR CODE
LG Washing Machine IE Error Code – What To Check? - How To Clear? I’m going to have to add a sediment filter where the water line comes into the house, otherwise I’ll have to keep cleaning out the washer’s filter. That seemed to correct the IE error problem. I cleaned out the filter and the silt that was in the filter tube area. (There is a black plastic or rubber circular piece under the mesh, but it remains in the tube.) Perhaps you could get the metal mesh filter out with a magnet, but it was in there pretty snugly. I deformed it a little, but I was able to get it back into shape. I gently pried my out with a screw driver. That was a waste of time, as the water inlet valve is behind the screen, and there is no way to get to the filter. Since the metal filter is domed outward, I took the machine apart, hoping I could reach it from the back side to push it out. Even though the plastic filters never clogged, the metal fine-mesh one behind it was completely clogged on Cold Water side.
LG WASHING MACHINE REPAIR MANUAL
I had already replaced the drain valve after constant DE error codes about 6 months ago.įred was right, I found a second filter behind the plastic one they show in the manual for my LG WT7200CW Washer. It just appears to flow out the back (after the prewash)ĭoes that sound like I need to replace the inlet valves or would there be a blockage or something else? I blew out hoses from inlet valve and they are fine.įinally I sat by a wash with the detergent compartment out and noticed that though the water seems to get in, and pushes out of the pre-wash (right ) side, it certainly doesn’t come out on the main wash (left) side. I must assume that this was always the case since the first IE error code, only noticed now that we changed to powdered detergent.
Now though we changed from liquid to powder detergent and we’ve noticed at the detergent compartment isn’t being used. This was obviously inconvenient as we would have to stay by the machine and couldn’t leave it to wash by itself. On my LG washer I have had issues with an IE error code for some while now, however we have just pressed ‘play’ and the wash had continued until the next cycle, then another IE code, and we would just press play again and it would finish. OEM WATER INLET VALVES FOR LG WASHERS ARE ABOVE IF WATER INLET VALVE IS FAULTY – REPLACE IT If you find that the water inlet valve is not working, you should replace it. You can test the valves with a multimeter to determine if it is faulty. You will need to get to the water inlet valve and check to be sure it is secure and the wire harnesses to power it are secure and connected properly. If all the above checked out, next you need to check the water inlet valve. LG WASHING MACHINE INLET VALVE FILTER SCREENSĤ – Get a large bucket to hold a few gallons of water.ĥ – Place the ends of both the HOT and COLD water valves into the bucket.Ħ – Turn the water valves on the wall to OPEN and run water through the hoses to test water flow and pressure.ħ – If water flows with no issues then you may have an issue with the water inlet valve. (Do not remove the water lines from the wall)ģ – While the water hoses are removed, check where the hoses connect on the washer and be sure the INLET VALVE FILTER SCREENS are not clogged. To check that water is flowing without interruption to the washer:ġ – Turn OFF the HOT and COLD water supply valves on the wall.Ģ – Remove the HOT and COLD water supply hoses FROM THE WASHING MACHINE. If the above 3 simple fixes all checked out good and no issues, next remove the water hoses to check for proper waterflow… 2 – Check and be sure the HOT and COLD water supply valves are fully open.ģ – Check that the HOT and COLD water supply hoses are not bent, damaged, or clogged with hard water.